69 Products Found

YE-RF-BT-A TACTILE TOUCH CONTROLLER PHONE W/ADAPTER   Y4E-CT-30-D TETHERED MONITOR OPERATOR STATION Same as above but the Tethered Control Station is supplied with a 30' (9m) long pre-connected cable.   A-DISP VALVE POSITION DISPLAY   Y4E-DISP MONITOR POSITION DISPLAY This display will show the stream position of any TFT RC electric monitor. Position is indicated by two sets of LEDs, one set for the vertical position and one set for the horizontal position. Buttons for the PARK & Oscillate features and HIGH/LOW speed selection are also supplied. A 10' (3m) long 4-conductor cable for power and communication is supplied pre-connected. When installed on systems w/RC Extend-A-Gun, the current state is indicated by LED (raised/lowered)   YE-RF-BT TACTILE TOUCH CONTROLLER PHONE ONLY   YC-RF-24 WIRELESS OPERATOR STATION 2.4 GHZ LONG DESCRIPTION   YC-RFRM-KIT ANTENNA & MONITOR MOUNTED O.S. KIT   Y4E-JS JOYSTICK MONITOR OPERATOR STATION This operator station allows any TFT RC electric monitor to be controlled using a joystick. Moving the joystick controls monitor vertical and horizontal movement. Thumb switches control nozzle pattern. A trigger built into the joystick handle can be used to open and close some water valves. The joystick is factory installed on an enclosure that houses the control electronics and a 10' (3m) cable is supplied with stripped wires for connection in the control system terminal box. The joystick control is also equipped with push buttons on top for PARK and OSCILLATE functions as well as monitor DEPLOY. An additional configurable button can be set up for RC Extend-A-Gun or LED light kit control. A toggle switch is available to select water valve open, close, or joystick control. The joystick control can be configured for proportional speed control of the horizontal and vertical axis. The joystick control is factory wired so that the AUX2 button on TFT monitor operator stations will also open and close the water valve. Mounting bracket meets NFPA 1900 9G force requirements which ensures the security of equipment and safety of personnel.   YE-PWR-COND POWER CONDITIONER ADAPTER LONG DESCRIPTION   YE-ABS-POS-1 ABSOLUTE POSITION UPGRADE KIT   YE-ETH-WIFI ETHERNET INTERFACE CONTROL FOR WIRED NETWORKS Same as above except for use with standard wireless Ethernet networks. Contact factory for configuration assistance.   Y4E-JS-GT-R JOYSTICK OPERATOR STATION   YE-VKG-PH GATEABLE VALVE KIT This valve kit includes a heavy-duty 2" NPT (50mm) water valve and an interface box for simplified 12/24 volt wire connections to the monitor control system. The valve is a 2" NPT (50mm) full port stainless steel ball valve with integral electric actuator control with valve opening position sensing and cable with pre-wired plug.   YE-ETHER ETHERNET INTERFACE CONTROL FOR WIRED NETWORKS This interface box enables a TFT RC monitor to be connected and controlled via a standard wired Ethernet network. This unit is designed to be operated from a PC or tablet running a standard web browser. The interface acts as a web server and no custom software is required. The interface box includes a pre-wired 10' (3m) cable with receptacle for monitor connections and a 10' (3m) cable for power connections and communication connections to other remote accessories (if any).   YC-RP PANEL MOUNTED OPERATOR STATION LONG DESCRIPTION   YE-VKG-PH GATEABLE VALVE KIT This valve kit includes a heavy-duty 2" NPT (50mm) water valve and an interface box for simplified 12/24 volt wire connections to the monitor control system. The valve is a 2" NPT (50mm) full port stainless steel ball valve with integral electric actuator control with valve opening position sensing and cable with pre-wired plug.   YC-VKG-PH VALVE KIT 2" NPT CANBUS   YE-RF-900-D WIRELESS MONITOR OPERATOR STATION WITH DISPLAY, 900 MHz Allows RC monitors to be controlled using a wireless handheld transmitter. The unit is easily configurable for multi-monitor control. This will allow a user to control up to ten TFT RC monitors from one operator station. The wireless transmitter will operate up to 500' (152m)away from the truck and is supplied with a stainless steel mounting bracket to securely store the handheld unit. This operator station includes a display for advanced system feedback and a backlit control panel for improved visibility of controls in low-light conditions. Mounting bracket meets NFPA 1900 9G force requirements which ensures the security of equipment and safety of personnel. See RC monitor installation & operation manual for operating frequency agency approvals or consult factory for agencies not listed. Order one radio & antenna for each RC monitor, listed below.   YE-VKG-PD GATEABLE VALVE KIT This valve kit includes a heavy-duty 1" NPT (25mm) water valve and an interface box for simplified 12/24 volt wire connections to the monitor control system. The valve is a 1" NPT (25mm) full port stainless steel ball valve with integral electric actuator control with valve opening position sensing and cable with pre-wired plug.   Y4E-JS-GT JOYSTICK MONITOR OPERATOR STATION WITH GATEABLE VALVE CONTROL Same as Y4E-JS-52 above but includes a valve opening adjustment slider to control the water flow, used with TFT gateable valve kit options.   YC-RF-RAD-24 WIRELESS OPERATOR STATION ANTENNA LONG DESCRIPTION   YE-VKG-PF GATEABLE VALVE KIT This valve kit includes a heavy-duty 1.5" NPT (38mm) water valve and an interface box for simplified 12/24 volt wire connections to the monitor control system. The valve is a 1.5" NPT (38mm) full port stainless steel ball valve with integral electric actuator control with valve opening position sensing and cable with pre-wired plug.   Y4E-JS-GT-NP JOYSTICK OPERATOR STATION   YE-RF-RAD-92 WIRELESS RADIO AND ANTENNA 920 MHZ   YE-VK VALVE CONTROL INTERFACE   Y4E-CT-100 TETHERED MONITOR OPERATOR STATION Same as above but the Tethered Control Station is supplied with a 100' long pre-connected cable.   Y4E-CT-10 TETHERED MONITOR OPERATOR STATION This operator station allows the electric monitor to be controlled from a handheld pendant. This operator station is supplied with a stainless steel mounting bracket to securely store the unit. The enclosure has an O-ring seal, liquid tight strain relief fitting with O-rings, and a membrane switch to keep water out. Any commands from this operator station will override commands made on the monitor control box. The pendant receptacle can be connected to the Panel Mount Operator Station or directly to the monitor through a customer supplied terminal block. A cable is supplied pre-connected to the panel-mounted receptacle and includes waterproof cap and chain. The Tethered Control Station is supplied with a 10' long pre-connected cable. This pendant plugs into a panel-mounted receptacle. This operator station is equipped with "last button pressed" software or can be configured as a "master" station. Mounting bracket meets NFPA 1900 9G force requirements which ensures the security of equipment and safety of personnel.   YE-VKG-PL VALVE KIT 3" NPT   Y4E-JS JOYSTICK MONITOR OPERATOR STATION This operator station allows any TFT RC electric monitor to be controlled using a joystick. Moving the joystick controls monitor vertical and horizontal movement. Thumb switches control nozzle pattern. A trigger built into the joystick handle can be used to open and close some water valves. The joystick is factory installed on an enclosure that houses the control electronics and a 10' (3m) cable is supplied with stripped wires for connection in the control system terminal box. The joystick control is also equipped with push buttons on top for PARK and OSCILLATE functions as well as monitor DEPLOY. An additional configurable button can be set up for RC Extend-A-Gun or LED light kit control. A toggle switch is available to select water valve open, close, or joystick control. The joystick control can be configured for proportional speed control of the horizontal and vertical axis. The joystick control is factory wired so that the AUX2 button on TFT monitor operator stations will also open and close the water valve. Mounting bracket meets NFPA 1900 9G force requirements which ensures the security of equipment and safety of personnel.   YE-RF-BT-I TACTILE TOUCH CONTROLLER PHONE ONLY   YE-CAN1 MULTIPLEX INTERFACE   YE-CAN2 MULTIPLEX ADAPTER SMALL PACKAGE   YE-ETH-WIFI ETHERNET INTERFACE CONTROL FOR WIRED NETWORKS Same as above except for use with standard wireless Ethernet networks. Contact factory for configuration assistance.   YE-RECEP-4 PANEL MOUNTED RECEPTACLE This receptacle allows tethered monitor operator stations to be connected at additional locations. A 30' (9m) long cable with a pre-connected receptacle is supplied. Includes waterproof cap and chain.   Y4E-JS-GT-R JOYSTICK OPERATOR STATION   Y4E-CT-100-D TETHERED MONITOR OPERATOR STATION Same as above but the Tethered Control Station is supplied with a 100' (30m) long pre-connected cable.   Y4E-TS TOGGLE SWITCH MONITOR OPERATOR STATION This operator station allows any TFT RC electric monitor to be controlled using three toggle switches. Switches control monitor vertical and horizontal movement plus nozzle pattern adjustment. The operator station can be surface mounted. A 10' (3m) long 4-conductor cable for power and communication is supplied pre-connected. This operator station is equipped with "last button pressed" software or can be configured as a "master" station.   Y4E-RP PANEL MOUNT MONITOR OPERATOR STATION This operator station allows the electric monitor to be controlled from a remote location and is designed to be flush mounted in a panel. This station may be used as the central location for terminating the wires from the monitor, incoming power, or hard wired inputs. All terminal blocks for wire connections are removable for easy terminating. The enclosure has an o-ring seal, liquid tight strain relief fittings with o-rings, and a membrane switch to keep water out. A 30' long cable for incoming power and communication connections is supplied pre-connected. This operator station is equipped with "last button pressed" software or can be configured as a "master" station.   YE-ETHER ETHERNET INTERFACE CONTROL FOR WIRED NETWORKS This interface box enables a TFT RC monitor to be connected and controlled via a standard wired Ethernet network. This unit is designed to be operated from a PC or tablet running a standard web browser. The interface acts as a web server and no custom software is required. The interface box includes a pre-wired 10' (3m) cable with receptacle for monitor connections and a 10' (3m) cable for power connections and communication connections to other remote accessories (if any).   YE-1F2M MONITOR CONNECTION HARNESS   YE-BT1 BLUETOOTH ADAPTER SMALL PACKAGE   YE-VK-PD VALVE KIT 1" NPT   YE-CAB-6 EXTENSION CABLE 4 CONDUCTOR   Y4E-JS-LT JOYSTICK OPERATOR STATION LT VERSION   Y4E-CT-10-D TETHERED MONITOR OPERATOR STATION WITH DISPLAY Allows RC monitors to be controlled from a handheld pendant and is supplied with a stainless steel mounting bracket to securely store the unit. The unit is easily configurable for multi-monitor control. This will allow a user to control up to ten TFT RC monitors from one operator station. This operator station includes a display for advanced system feedback and a backlit control panel for improved visibility of controls in low-light conditions. The enclosure has an O-ring seal, liquid tight strain relief fitting with O-rings, and a membrane switch to keep water out. The pendant receptacle can be connected to the Panel Mount Operator Station or directly to the monitor through a customer supplied terminal block. A cable is supplied pre-connected to the panel-mounted receptacle and includes waterproof cap and chain. The Tethered Control Station is supplied with a 10' long pre-connected cable that plugs into a panel-mounted receptacle. This operator station is equipped with "last button pressed" software or can be configured as a "master" station. Mounting bracket meets NFPA 1900 9G force requirements which ensures the security of equipment and safety of personnel.   YE-RF-920 WIRELESS OPERATOR STATION 920 MHZ   YE-RECEP-4 PANEL MOUNTED RECEPTACLE This receptacle allows tethered monitor operator stations to be connected at additional locations. A 30' (9m) long cable with a pre-connected receptacle is supplied. Includes waterproof cap and chain.   Y4E-JS-LT JOYSTICK OPERATOR STATION LT VERSION   Y4E-CT-100-D TETHERED MONITOR OPERATOR STATION Same as above but the Tethered Control Station is supplied with a 100' (30m) long pre-connected cable.   YE-ETH-PLC ETHERNET INTERFACE CONTROL FOR WIRED NETWORKS This interface box enables a TFT RC monitor to be connected and controlled via an industrial type programmable logic controller (PLC). Contact customer service for list of compatible PLCs. Same cabling supplied as units above.   Y4E-CT-10-D TETHERED MONITOR OPERATOR STATION WITH DISPLAY Allows RC monitors to be controlled from a handheld pendant and is supplied with a stainless steel mounting bracket to securely store the unit. The unit is easily configurable for multi-monitor control. This will allow a user to control up to ten TFT RC monitors from one operator station. This operator station includes a display for advanced system feedback and a backlit control panel for improved visibility of controls in low-light conditions. The enclosure has an O-ring seal, liquid tight strain relief fitting with O-rings, and a membrane switch to keep water out. The pendant receptacle can be connected to the Panel Mount Operator Station or directly to the monitor through a customer supplied terminal block. A cable is supplied pre-connected to the panel-mounted receptacle and includes waterproof cap and chain. The Tethered Control Station is supplied with a 10' long pre-connected cable that plugs into a panel-mounted receptacle. This operator station is equipped with "last button pressed" software or can be configured as a "master" station. Mounting bracket meets NFPA 1900 9G force requirements which ensures the security of equipment and safety of personnel.   Y4E-CT-30 TETHERED MONITOR OPERATOR STATION Same as above but the Tethered Control Station is supplied with a 30' long pre-connected cable.   YC-RP-01 PANEL MOUNTED OP STATION FOR AERIALS   YE-VK-PH VALVE KIT This valve kit includes a heavy-duty 2" NPT (52mm) water valve and an interface box for simplified 12/24 volt wire connections to the monitor control system. The valve is a 2" NPT (52 mm) full port stainless steel ball valve with integral electric actuator control and cable with pre-wired plug   YC-RM MONITOR MOUNTED OPERATOR STATION LONG DESCRIPTION   Y4E-TS TOGGLE SWITCH MONITOR OPERATOR STATION This operator station allows any TFT RC electric monitor to be controlled using three toggle switches. Switches control monitor vertical and horizontal movement plus nozzle pattern adjustment. The operator station can be surface mounted. A 10' (3m) long 4-conductor cable for power and communication is supplied pre-connected. This operator station is equipped with "last button pressed" software or can be configured as a "master" station.   YE-VK-PL VALVE KIT This valve kit includes a heavy-duty 3" NPT (76 mm) water valve and an valve interface control box for simplified 12/24 volt wire connections to the monitor control system. The valve is a 3" NPT (75 mm) full port stainless steel ball valve with integral electric actuator control and cables with pre-wired plugs.   YE-VK-PF VALVE KIT This valve kit includes a heavy-duty 1.5" NPT (38mm) water valve and an interface box for simplified 12/24 volt wire connections to the monitor control system. The valve is a 1.5" NPT (38 mm) full port stainless steel ball valve with integral electric actuator control and cable with pre-wired plug.   YC-TS TOGGLE SWITCH OPERATOR STATION LONG DESCRIPTION   YE-1F3M MONITOR & VUM CONNECTION HARNESS   YE-1F2M MONITOR CONNECTION HARNESS   YE-ETH-PLC ETHERNET INTERFACE CONTROL FOR WIRED NETWORKS This interface box enables a TFT RC monitor to be connected and controlled via an industrial type programmable logic controller (PLC). Contact customer service for list of compatible PLCs. Same cabling supplied as units above.   Y4E-JS-GT-LT JOYSTICK OPERATOR STATION LT VERSION   YE-BT1 BLUETOOTH ADAPTER SMALL PACKAGE   Y4E-CT-30 TETHERED MONITOR OPERATOR STATION Same as above but the Tethered Control Station is supplied with a 30' long pre-connected cable.   YC-RP-01 PANEL MOUNTED OP STATION FOR AERIALS   Y4E-COMM MONITOR COMMUNICATION INTERFACE BOX This communication interface box converts discrete input signals into communications for controlling any TFT RC electric monitor. The discrete input signals can be from a joystick, installer supplied toggle switches, relay contacts or canbus output module. The interface box accepts +12/24 VDC signals, but can be field changed to accept ground signals. This interface box also includes a relay to indicate when the monitor is in PARK position and has contacts that can be connected into the door open or Extend-A-Gun raised warning light. The interface box can be surface mounted. A 10' (3m) long 4-conductor cable for power and communication is supplied pre-connected. Also a 10' (3m) long cable is supplied pre-connected for connection to the input signals. This interface box is equipped with "last button pressed" software or can be configured as a "master" station.   YE-RF-920 WIRELESS OPERATOR STATION 920 MHZ   YC-RM MONITOR MOUNTED OPERATOR STATION LONG DESCRIPTION